Description
QTY |
Description |
| 1 | Arduino(Compatible) UNO R3 with USB Cable |
| 1 | CNC shield v3.00 |
| 4 | Stepper Driver – DRV8825 |
| 1 | Fan – 40×40 24V |
| 1 | MEAN WELL Power Supply – 24V 350W |
| 1 | 4 Core Shielded Cable (use for X Axis, Y Axis, Z Axis and A Axis with proper length for convenience) |
| 1 | 2 Core Shielded Cable (use for X Axis, Y Axis, Z Axis and A Axis with proper length for convenience) |
| 1 | DC Power Cable |
| 1 | Ground Wire |
| 4 | 4 Pin Dupont Wire |
| 3 | 2 Pin Dupont Wire |
| 4 | Terminal Block (4 Pole) |
| 3 | Terminal Block (2 Pole) |
| 1 | E-Stop Switch + E-Stop Cable |
| 3 | Limit Switch Kits |
| 4 | Welding-free plug-in terminal block |
| 10 | Black Mini Jumpers |
| 4 | Nema Stepper Motor 1.26N.m |
More Details:
The Controller comes is made up of the following items:
- Arduino UNO Compatible
- 14 digital input/output pins – 6 pins can be used as PWM outputs
- 6 analog inputs
- 16 MHz crystal oscillator
- Operates at 5V
- Recommended input voltage range: 7V to 12V
- Flash Memory: 32 KB (0.5KB used by bootloader)
- SRAM: 2KB
- EEPROM: 1KB
- CNC Shield V3
- Version 3.00
- 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total) - Uses GRBL as control software
- Power supply: DC 12-36V
- Interface: mini-USB
- Maximum stepper motor current: less than 2A 2 phase 4 wire stepper motor
- Over 1A stepper motors must use heat-sinks and/or other cooling (fan)
- DRV8825 Stepper Drivers
- Low RDS (ON) outputs
- Automatic current decay mode detection / selection
- Internal UVLO
- Mixed with slow current decay modes
- Synchronous rectification for low power dissipation
- Crossover-current protection
- Thermal shutdown circuitry
- 3.3 and 5 V compatible logic supply
- Ground Fault Circuit
- Load short-circuit protection
- Six microstepping modes: full, 1/2, 1/4, 1/8, 1/16 and 1/32
- Fan – 40x40mm 24V
- Dimensions: 40mm (L) x 40mm (W) x 10mm (H)
- Rated Voltage: 24V
- Current: 0.10A
- Input Power: 0.84W
- Nominal Speed: 6000 RPM
- Air Flow: 5.75 CFM
- Noise: 24 dBA
- Wire Length: 250mm
- Connector: 2pin 2.54mm
Power:
- MEAN WELL Power Supply – 24V 350W
- Output Voltage-Channel: 24 V
- Output Power: 350.4 W
- Enclosed Case
- Input Voltage: 90 VAC to 132 VAC/180 VAC to 264 VAC, 240 VDC to 370 VDC
- Output Current-Channel: 14.6 A
- Mounting Style: Chassis
- Length: 215 mm
- Width: 115 mm
- Height: 30 mm
- Input Frequency: 47 Hz to 63 Hz
- Unit Weight: 760 g
Cables & Connectors:
- 4 Core Shielded Stepper Cables terminated at one end with JST SM 4P (Connector to Stepper Motors)
- 2 Core Shielded Signal Cables terminated at one end with JST SM 2P
- DC Power Cable
- 22 AWG
- 1 x 500mm
- Ground Wire
- 20 AWG
- 1 x 500mm
- Stepper Cables (CNC Shield to Connectors)
- Dupont Female
- Connector at one end
- 4 x 300mm
- EStop Cable
- 22 AWG
- 1 x 1000mm
- 4 x Terminal Block 5 Pole
- 3 x Terminal Block 3 Pole
Signal:
- 3 x Limit Switch Kits
3 x Micro Limit Switch
3 x Limit Switch Plate
6 x M3 10mm Cap Head Screw
3 x M5 8mm Low Profile Screw
3 x M5 Drop-in Tee Nut - NOTE: The holes in the switch will need to be opened a little (3mm drill bit) to allow for the M3 screw or alternatively you can use a M3 tap to cut a thread into the plastic.
- 1 x E-Stop Switch
-
- Max Current: 10A
- Max Voltage: AC 660V.
- Rated Load:
-
- AC: 220VAC/6A, 380VAC/4A, 660VAC/2A
- DC: 440VDC/0.3A, 220VDC/0.5A, 110VDC/1A
- TYPE: N/C
- Withstand Voltage: 2500V /60S
- Temperature: -25°~+55°
- Contact resistance: <25mΩ
Regarding our Shielded Cables:
- The 4 core and 2 core shielded cables by bulkman3d are cut in the proper length for customers convenience which meet the needs and multifunction of different size of our CNC Machine.
- This high quality 4 core cable has 2 layers of insulation and 2 shield layers to reduce signal interference and maximuse efficiency.
- The four insulated wires are shielded by oxygen free tinned annealed copper wire braid with Aluminium/PET tape (100% coverage) to shield the cores from EMF interference.
- This is again insulated by a thick clear layer of thermoplastic sheath insulation. Suitable for applications requiring electrical/electronic screening of cable. 22AWG suitable for 300V DC and up to 80°C
Wiring Schematic:
IMPORTANT NOTE:
NEVER connect or disconnections any wire while power is applied.
ALWAYS disconnect power before making any connections or disconnections.
Failure to do the above will result in damage to the stepper drivers.
Software:
Links:
Note : Any Mains power connections must be installed by a Licensed electrician or suitability qualified person.
